Type 1 boards cover the following earlier non-consult vehicles:
Equipment
NIStune Type 1
Board
Type 1 boards cover the following earlier
non-consult vehicles:
CR31 Skyline (RB30E)
HR31 Skyline (NICS/ECCS RB20DET)
VL/Turbo Commodore (RB30E/RB30ET)
Z31 300ZX (VG30E, VG30ET) 1984-1985, 1986, 1987-1989
A31 Cefiro (RB20DET)
J30 Maxima (VG30E)
S13 Silvia (CA18DE/DET)
S13 Stanza / 240SX (KA24E)
N13 Pulsar (CA16DE)
N13 Pulsar (CA18DE)
U12 Bluebird (CA18DE)
Type
1 Hardware Install Sheet
This is a first for older non-consult ECUs!
You can now view and log RPM, Speed, MAF voltage, O2 sensor, Temperature, Battery, Timing and various switch settings. Diagnostic Terminal Codes can monitored and cleared. You can also perform real time tuning with this board!
This board along with the NIStune software provides consult capabilities (including Diagnostic reporting) and map tracing for non-consult Nissan ECUs
Current price is $420AUD for
board, USB cable and NIStune Software (Individual Users License) and
documentation set. Additionally, shipping and transaction fees may apply. (GST inclusive price inside Australia $462AUD)
Provided with USB connector, CPU connector, 28 pin socket, USB cable and instructions
NIStune Type 2 Board
Type 2 boards cover the following earlier consult
vehicles:
M30 Infiniti (VG30DE)
Z32 Fairlady 300ZX (VG30DETT)
[Note ECR33 RB25DET Skyline can use Z32 VG30DETT ECU with minor wire swapover]
HCR32 Skyline (RB20DET)
BNR32 Skyline (RB26DETT)
[Note BNCR33, BNR34 Skylines can use BNR32 RB26DETT ECU and O2 sensors]
U12 Bluebird (KA24E)
NOTE: Q45 (VH45DE) Work with NIStune but require an emulator. ROM image too big
for Type 2 board
NIStune uses a daughter board as an alternative to an emulator or EPROM chip for real-time tuning using a modified version of Nissan Consult. It provides faster transfer rates, realtime modification of maps, constants and tables using the NIStune software.
Current price is $420AUD for board and NIStune Software (Individual Users License) and documentation set. Additionally, shipping and transaction fees may apply. (GST inclusive price inside Australia $462AUD)
Provided with CPU connector, 28 pin socket and instructions
Note: Nissan Consult connector to be purchased separately. You can get these in USB versions ($95AUD / $104.50 Australia inc GST) from www.plmsdevelopments.com and purchased through us.
NIStune Type 3 Board
Type 3 boards cover the following earlier consult
vehicles:
NIStune uses a daughterboard for realtime tuning using a modified version of Nissan Consult. It provides faster transfer rates, realtime modification of maps, constants and tables using the NIStune software.
Current price is $440AUD for board, NIStune Software (Individual Users License) and documentation set. Additionally, shipping and transaction fees may apply. (GST inclusive price inside Australia $484AUD)
Provided with 40 pin header adaptor connector and instructions
Note: Nissan Consult connector to be purchased separately. You can get these in USB versions ($95AUD / $104.50 Australia inc GST) from www.plmsdevelopments.com and purchased through us also.
NIStune Type 4 Board
Type 4 boards cover the following later consult
vehicles:
B14 NX2000 (SR20DE) [upto 1995 only]
N15 Pulsar (GA16DE)
G20 Infiniti P10 (SR20DE) [upto 1995 only]
S13 180SX "Type R" / "Type X" (SR20DET)
S14A Silvia/200SX (SR20DET)
S15 Silvia/200SX (SR20DET)
S14 240SX (KA24DE)
ER34 Skyline (RB25DET)
WC34 Stagea late [JECS ECU only] (RB25DET)
U13 Altima (KA24DE) [upto 1995 only]
Y33 Cedric (VQ30DET)
Type
4 Hardware Installation
Manual
NIStune uses a daughterboard for realtime tuning using a modified version of Nissan Consult. It provides faster transfer rates, realtime modification of maps, constants and tables using the NIStune software.
Current price is $460AUD for board, NIStune Software (Individual Users License) and documentation set. Additionally, shipping and transaction fees may apply. (GST inclusive price inside Australia $506AUD)
Provided with 40 pin header connector and instructions
Note: Nissan Consult connector to be purchased separately. You can get these in USB versions ($95AUD / $104.50 Australia inc GST) from www.plmsdevelopments.com and purchased through us also.
NIStune Type 5 Board (Coming soon)
Type 5 boards will cover the following later consult
vehicles:
S14 Silvia (SR20DE) Half size ECU
B13 Sentra (GA16DE) Half size ECU
K11 Micra (CG10) Half size ECU
This is our current work in progress....
Update 1 Sep 2009 - We are
working on a USB only base image programmer to support this board. The
original base image programmer worked via parallel port and was based
from the Willem design. It did not have enough I/O capability from the
PC to support the multiplexed bus operation this board requires for
programming. We have put a design of the programmer together and that
is currently getting laid out and the firmware for the programmer is
now in work. No ETA yet but hopefully within two months!!
NIStune Type 6 Board (TBD)
We are thinknig about doing a board for R33 RB25DE/RB25DET but it involves a fair amount of work, and the parts to interface with the existing 84 pin MCU on this ECU. It is a very difficult board to get started on and requires whole new firmware code to be implemented, whilst supporting customers with our existing product line. I will start drafting schematics once Type 5 has been finished and we have got the knock sensing functionality working.
If you are looking for something to get these going then we suggest either using a HCR32 Skyline or Z32 300ZX ECU with a Type 2 board. See our FAQ topics for more information regarding these ECUs.
Your other option, if you really want to use the R33 ECU is to use an emulator with an expensive third party daughter board (pictured above) available from Sam at www.drdrift.com.au
NIStune Base Image Programmer Boards
NIStune boards are preprogrammed with your ECU ROM image when you place your order. The base image programmer boards take Type 1, Type 2 and Type 3 boards. These will also take Type 4 boards when these are available. They require a PC with parallel port and USB port or 5 - 12 volt power supply.
Workshops may wish to order blank boards which they can preprogram as required. We will be providing programmer boards (Cost $140AUD) which will initially be available to workshops to reprogram their own boards. We have produced our first small batch of working programmer boards at this time.
Note: NIStune programmers cannot be used for reading / programming standard EPROM chips. You will require a Moates, Willem or similar programmer
Wide Band
The following wide band units are supported by Nistune and can be used in conjunction with consult for AFR and auxiliary input display, map tracing and logging / replace. Capabilities depend on which unit you purchase, so research before purchasing.
We personally use the TechEdge and Innovate LC-1 units, but most do about the same job with different auxiliary functions.
TechEdge
1.5 and 2.0
http://www.techedge.com.au
Innovate
LM-1 and LC-1
http://www.innovatemotorsports.com
Note:
Regarding LM-2 units we are still waiting for Innovate to release an updated
Software Development Kit (SDK) for this unit so we can communicate with the unit
using the USB connection. In the meantime several users have ordered an extra
serial lead with the unit to use it with the previous LM-1 SDK and Nistune.
AEM
UEGO
http://www.aempower.com
Zeitronix
http://www.zeitronix.com
PLX
Devices (R Series)
http://www.plxdevices.com
MOTEC
PLM
http://www.motec.com.au/plm/plmoverview
Just Another Wideband
http://www.14point7.com
VEMS Wideband
http://www.vems.co.uk
DLP Design A/D Converter
http://www.dlpdesign.com/usb/io8.shtml
Read upto one AFR input and
6 configurable A/D inputs from the DLP A/D converter. Plug in any wideband
device with 0-5 volt output and watch and log it in NIStune.
Emulation (Intronics Romulator / Moates Ostrich)
For those who wish to use emulation instead of built in boards Using a single emulator will allow you to realtime tune your 8-bit ECU board using the Consult for ECU status and accurate maptracing. Motes Ostrich 2.0 emulators now have hardware maptracing supported for 8-bit ECUs only in NIStune
Using dual emulators combined with a commercially available daughterboard for 16-bit ECUs using Consult for ECU status and accurate maptracing.
Emulation (CalumSult RealTime Board)
We can confirm that NIStune software is now compatible with CalumSult real-time boards. This means that you no longer have to use three separate programs to emulate, data log, map trace and read wideband readings on. NIStune integrates all the data together in one package and can display and data log all information together.